Our Website Family: TunerSports.com ClubCivic.com ClubIntegra.com
Attention Acura Integra Visitor:  Remove this block by logging in above or r

Welcome to ClubIntegra.com.

A forum dedicated to the Acura Integra, including all generations. In order to post on this forum you will have to register.

Registration is free and will entitle you to other site features including access to post your Acura Integra in the member's garage, join in raffles for performance parts, etc.

To start viewing messages by generation, select the Acura Integra forum that you want to visit from the list below. Or view all Acura Integra forums.

Go Back   ClubIntegra.com - Acura Integra Forum > Acura Integra Technical > All Motor / Drivetrain

Notices

Please SEARCH before posting a new thread. ->
Ready to Post a New Thread/Question? ->



B series Torque Specs

All Motor / Drivetrain



Closed Thread
 
Thread Tools Rate Thread Display Modes
Old 09-08-2009, 02:53 AM   #1
Samurai_Blue
Is best bro.
 
Samurai_Blue's Avatar
 
Join Date: Jul 2008
Location: Nor*Cal
Age: 24
Posts: 22,904
 
iTrader: (15)

Send a message via AIM to Samurai_Blue Send a message via MSN to Samurai_Blue
Default B series Torque Specs

ALL Credit goes to google as well as stinky turbo at b20vtec.com

CYLINDER HEAD BOLT TORQUE SPECS (tightening) / (loosening)
8, 4, 2, 6, 10 <---intake order 3, 7, 9, 5, 1
7, 3, 1, 5, 9 <---exhaust order 4, 8, 10, 6, 2

Torque in steps: 22ft-lbs (264in-lbs), Then to 63ft-lbs (756in-lbs) (final spec) 94+ Teg
Torque in steps: 22ft-lbs (264in-lbs), Then to 61ft-lbs (732in-lbs)(final spec) 90-93 Teg / B16's


CAMSHAFT COVER SPECS
13, 9, 5, 1, 3, 7, 11 (side of cam cover closest to intake)
14, 10, 6, 2, 4, 8, 12 (side of cam cover closest to exhaust)

Shown above is one cam cover, sequence is the same for intake and exhaust cam cover.

#1-10 20ft-lbs (240in-lbs) #11-14 7.2ft-lbs (86in-lbs) (94+ B18C specs)
#1-10 16ft-lbs (192in-lbs) #11-14 8ft-lbs (96in-lbs) (B16A specs)
**not sure what the specs are for non-VTEC motors, sorry**

Seat each camshaft by pushing it towards the dizzy side of cylinder head.

VALVE COVER SPECS
7______________5______(Intake side of valve cover)
_____3____1____
_____4____2____
8______________6______(Exhaust side of valve cover)

7.2 ft-lbs (86in-lbs) (all B series)

FLYWHEEL TORQUE SPECS
_______1
_____6___8
___4_______3
_____7___5
_______2

Torque in steps: 19ft-lbs (228in-lbs), 38ft-lbs (456in-lbs), 57ft-lbs (684in-lbs), Then to 76ft-lbs (912in-lbs) (all B series)

PRESSURE PLATE TORQUE SPECS
_______1
_____6___3
_____4___5
_______2

Torque in steps: 5ft-lbs (60in-lbs), 10ft-lbs (120in-lbs), 14ft-lbs (168in-lbs), Then to 19ft-lbs (228in-lbs) (all B series)

FUEL FILTER BANJO BOLT
25ft-lbs (300in-lbs) (94+ Teg specs)
16ft-lbs (192in-lbs) (90-93 Teg / B16 / 89-91 Civic CRX specs)

FUEL FILTER SERVICE BOLT
11ft-lbs (132in-lbs) (94+ GSR specs)
9ft-lbs (108in-lbs) (90-93 Teg / B16 / 89-91 Civic CRX specs)

HEADER A-PIPE TO B PIPE (x3)
40ft-lbs (480in-lbs) (all B series)

B PIPE TO CAT (x2)
12ft-lbs (144in-lbs) (all B series)

SHIFT LINKAGE EXTENSION ROD TO TRANNY BOLT (8x1.25mm)
16ft-lbs (192in-lbs) (90+ Teg specs)
12ft-lbs (144in-lbs) (B16 specs)

SPEED SENSOR TO TRANNY BOLT
9ft-lbs (108in-lbs)

ALTERNATOR TOP BOLT
17ft-lbs (204in-lbs) (all B series)

ALTERNATOR BOTTOM BOLT
33ft-lbs (396in-lbs) (all B series)

CRANKPULLEY BOLT
130ft-lbs (1560in-lbs) (90+ Teg)

If the crankpulley bolt is new:
145ft-lbs (1740in-lbs) loosen it a little, then re-tighten to 130ft-lbs (final spec)

87ft-lbs (1044in-lbs) (B16A, first gen)
**not sure what torque is for B16A2 and B16A3's**

TIMING BELT TENSIONER
40ft-lbs (480in-lbs) (all B series)

DRIVER SIDE BRACKET TO BLOCK (x3)
40ft-lbs (480in-lbs) (all B series)

DRIVERS SIDE BRACKET STUD & BOLT
54ft-lbs (648in-lbs) (all B series)

DRIVER SIDE ENGINE TO CHASSIS MOUNT BOLT
40ft-lbs (480in-lbs) (all B series)

TRANNY MOUNT TO TRANNY BOLTS (x3)
54ft-lbs (648in-lbs) (all B series)

TRANNY MOUNT TO CHASSIS BOLT
40ft-lbs (480in-lbs) (all B series)

REAR ENGINE BRACKET TO TRANNY BOLTS (x3)
43ft-lbs (516in-lbs) (1 passenger side) 86.8ft-lbs (1041in-lbs) (2 driver side) (94+ Teg specs)
43ft-lbs (516in-lbs) (90-93 Teg / B16 specs)

REAR ENGINE BRACKET TO MOUNT BOLT
43ft-lbs (516in-lbs) (all B series)

REAR MOUNT TO REAR SUBFRAME BOLTS (x3)
43ft-lbs (516in-lbs) (all B series)

TRANNY TO BLOCK BOLTS (x5)
47ft-lbs (564in-lbs) (all B series)

LONG AND SHORT STARTER BOLTS
33ft-lbs (396in-lbs) (all B series)

CLUTCH COVER LOWER BOLTS (8mm)
17ft-lbs (204in-lbs) (all B series)

CLUTCH COVER UPPER BOLTS (6mm)
9ft-lbs (108in-lbs) (all B series)

INTERMEDIATE SHAFT TO BLOCK BOLTS (x3)
28ft-lbs (336in-lbs) (all B series)

FRONT AND REAR STIFFENER TO TRANNY BOLT
42ft-lbs (504in-lbs) (all B series)

FRONT AND REAR STIFFENER VERTICAL BOLTS
17ft-lbs (204in-lbs) (all B series)

INTAKE MANIFOLD BOLTS
17ft-lbs (204in-lbs) (all B series)

EXHAUST MANIFOLD BOLTS
23ft-lbs (276in-lbs) (all B series)

BALL JOINT CASTLE NUT
40ft-lbs (480in-lbs)

LCA TO DAMPER FORK LOWER NUT
47ft-lbs (564in-lbs)

DAMPER FORK UPPER BOLT
32ft-lbs (384in-lbs)

32mm AXLE SPINDLE NUT
134ft-lbs (1608in-lbs)

OIL DRAIN PLUG
33ft-lbs (396in-lbs) (all B series)

TRANNY FILL PLUG
33ft-lbs (396in-lbs) (all B series)

TRANNY DRAIN PLUG
29ft-lbs (348in-lbs) (all B series)

SPARK PLUGS
20ft-lbs (240in-lbs)
__________________

Mishimoto | Tuner Sports | Garage Star | Raceline USA | Build | Instagram: @DylonFujiFilm
Samurai_Blue is offline  
Old 09-08-2009, 02:58 AM   #2
Samurai_Blue
Is best bro.
 
Samurai_Blue's Avatar
 
Join Date: Jul 2008
Location: Nor*Cal
Age: 24
Posts: 22,904
 
iTrader: (15)

Send a message via AIM to Samurai_Blue Send a message via MSN to Samurai_Blue
Default









__________________

Mishimoto | Tuner Sports | Garage Star | Raceline USA | Build | Instagram: @DylonFujiFilm
Samurai_Blue is offline  

Closed Thread




Similar Threads
Thread Thread Starter Forum Replies Last Post
question about torque specs 93da-t 2nd Generation Acura Integra (1990-1993) 4 08-24-2011 11:17 AM
torque specs b18a1? luvda2ndgenteg 2nd Generation Acura Integra (1990-1993) 5 04-01-2011 12:37 PM
need torque specs for tighning gs300cky All Motor / Drivetrain 2 03-16-2011 04:42 PM
head torque specs Jayman 3rd Generation Acura Integra (1994-2001) 1 06-18-2009 12:21 AM

Thread Tools
Display Modes Rate This Thread
Rate This Thread:

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

All times are GMT -4. The time now is 06:42 PM.


Store News:

Latest Topics:


Store Specials:








Find this site helpful? Donations are appreciated.


Powered by vBulletin® Version 3.8.5
Copyright ©2000 - 2014, Jelsoft Enterprises Ltd.
vB.Sponsors
Forum SEO by Zoints