Search results

Does anyone happen to know if front spindles from a 92-95 civic will work on my 96 teg? I have a lower balljoint going bad and I have a parts civic in the garage with new balljoints. Thanks

Ok so I got bored and decided to do a compression test on my b20 which is in my 96 teg and ran great before this. Came up with 160ish on all 4. So I put the plug wires back on and start my car. It runs like absolute shit. It sounds like the timing is way off. I triple checked everything and...

I finally got my bumper and lights on. Sprayed a few primer coats for now. Hopefully it will go in for paint this winter.

So I had an extra sitting around and decided to strip, sand and repaint. It didnt come out the best, but not bad for a rattle can job. Comments are welcome.

Ok heres the deal. Back on dec29 I put new tie rods, springs, and new tires on my teg. That same day I took it to goodyear to get it aligned. Well a couple of days ago I started to hear a clicking noise when I hit bumps and when I turned the steering wheel. Tonight I got home from work and...

Any chance I can get someone to snap a pic of their exhaust where the header meets the pipe. I just bought a cat back system and I dont have a cat and need some pictures to determine what I need to buy. Thanks

My teg is throwing cel 45. fuel system too rich or too lean. My question is, what could be the problem? Thanks for any help.

Has anyone ever heard of these? http://cgi.ebay.com/ebaymotors/94-02-INTEGRA-RS-LS-GSR-ADJUSTABLE-FRONT-CAMBER-KIT-BK_W0QQcmdZViewItemQQcategoryZ33581QQihZ016QQitemZ260165414215QQrdZ1QQsspagenameZWDVW I need a front camber kit but I dont need anything too blingy, just something that will...

Ok I have most of what I need. My question is, do I need to change the tranny mount or is there a bracket? Another question, I have the trans, clutch kit, resivoir, line, pedals and a manual ecu. Besides the starter, shift linkage and mount, is there anything else that I will need? I finally...

Anyone have any ideas on what is causing this? The drivers side wheel sits further back then the passenger wheel. I have replaced the front lca and the upper control arm. All bushings look to be fine and there isnt any obvious damage. The car has been like this since my brother inlaw owned it...

Yep, came home to see my new shoes.

Anyone know if a moon roof from a 5th gen civic will fit in my 96 teg? When I hit the switch to open it, it chatters like hell like its getting hung up. I have lubed up the rails and its still the same. I also noticed that under the rubber, the glass frame is starting to rust a bit. I have a...

Ok so my brother and I are heading home from work and get stuck in a cunstruction zone with no way to turn around or anything. Then the storm hits. I havent been this scared in a long time, only beacuse there was no way out. Heres a short vid. My buddy called me a few minutes later and told me...

This is kind of a dumb question. I have a 96 ls and I have seen ecu's on ebay that say obd1. However I was assuming I was obd2. Can someone enlighten me?

My new center caps came today. Tell me what you think. Can anyone guess what they're from?

I'm being kinda lazy and dont feel like searching too far so I'll ask here. On average how many miles per tank should one expect from a 96 auto b20 teg? My mpg has been depressing me, less then 300 a tank. No engine light, so I dunno what the deal is.

Ok heres the deal, I am planning on swapping heads within the next couple weeks and running obd1. I have a chipped p30 ecu and need to know if I can run it with my auto trans for now? I have a maual trans but need to gather the rest of the parts to do the conversion. I know that an auto ecu will...

Heres some goodies I just got. Will have them installed soon. Hope you like the pink ass shag carpet

Ok as some of you may know, I have an auto b20. Well I have come accross a great deal on a b16 head with gsr cams and everything needed to convert. dizzy, harness ect. I was told that someone sells the dowell (sp) pins for this setup so I wont have todo any drilling or anything. Does anyone know...

Does anybody know if 205's will fit my oem 96 ls steelies? I know factory is 195 60 14. I was just wondering if 205's would be too wide.