Search results

Well after my failed attempt to sell it i moved it to a farm where it would be safe. I managed to com up with a slew of new parts. New ECU, Radiator, Cylinder Head, Battery, Battery Box, motor mounts, I got the engines bottom end gone through by a local shop. I'm still hunting down why the Check...

yeah sorry if i wasnt specific i actually have a relay sitting in the way that way i dont blow out the circuit i attach it to. i actually did run it inside it was easier than expected.

anyone know what wires in the engine bay of a gen 2 integra come on with the key? i need a circuit that comes on with the key for the aftermarket fan i installed.

even when i jump the port the light stays solid. its solid and gives no code. but it only comes on without the port jumped after the engine comes up to idle after initial start up. its not on when i first start the car but comes on after its supposed to switch into run mode for the computer its...

it doesn't turn off though its just a solid light

ok yeah its not just one long light and a then off for a bit before it comes back like it would be fore an O2 its 1 solid light continuous it never goes out. which is what i count as a 0 i think and not a 1 but i could be wrong?

i get one long light when i check the codes which means ecu correct? if this is the case anyone got an extra OBD1 PR4 around i could buy?

thanks guys, i checked and double checked. so i had a shop do a leak down and it was fine the sensor its self was what was bad the air was from a hose note quite tight enough

ok guys i know how to fill the coolant levels so yeah its not the weeper or me lol. anyway i have replaced the waterpump, and thermostat and still its overheating. I am coming up with i either have a bad head or a cracked block because bubbles continue lightly coming out of the radiator and if i...

I do want to say you guys have been a big help with things so far and this car is coming together thanks to the quick answers i get and when i have the time im usually able to find either the same problem as someone else or my problem is mentioned in an answer for another question. So thanks to...

ok finally got the high RPM weirdness taken care of now i have a new thing lol. Anyway i know how to set timing, you jump the gray connector while doing so the computer does not fight you. any way now when i start the car the CEL is off after about a minute it turns on but when i try to check it...

as i stated in the title i got the car put back together i had the head off to have it checked for bent valves. i changed the gaskets out and changed the fuel filter i seem to have all of the electrical ports in place but i may have missed one what would cause it to rev all the way to max but...

thanks i was waiting on that, and for sure that thing was way higher than that when i took it off.

Just wondering just how tight the banjo bolt needs to be on the engine side of the filter. When i took off the old one it was very very tight and im wondering is there an official torque spec for it ?:)

I wish i could but the now removed head unit is from a company that apparently no longer is in business so i am stuck between a rock and a hard place.

Ok its a simple question and im sure there is a simple answer, When i got my wonderful Integra the previous owner had sadly destroyed the radio wiring harness by the method of cutting the original plugs and using the twisted wire duct tape method installed the head unit into the car. Now the...

yeah i think that's most of it only things missing are the rods i think from reading the description thank you though that helps a ton :)

1993 LS, i have looked on google and keep having a difficult time finding piston and rod kit i know many guys like to swap motors in these cars but i just want to do a simple rebuild of the original as is my style to remain stock :D but yeah i dunno if its my computer (might have a virus) or...

93 LS Here Honestly i dunno what to think of it :P but 1400$ ago i didn't have a car and the rest of the house did so there is that... Ignore the date stamp the camera's batteries were just replaced and i didnt reset the date