Search results

On my way back from Honda Day a few weeks ago, my car developed a sputtering bucking under load, car drove great that whole weekend and most of the drive home. Car drives fine unless I accelerate ~50% or so, it's not boost or rpm dependant. Sometimes I will hit boost with no issues, and has...

I bought a generic b series intercooler piping kit, I have a mishimoto Z line. The piping fits fine and would be the right fit for most setups except for one small issue. The turbo sits far too low for a straight coupler and 90 pipe. I'm looking for some input on fixing this. I was thinking of...

So I purchased this mani and turbo a while back, they've been run before so I know they can work. However, the measurements on the flanges are slightly different. The bolt holes line up, but the gasket my kit sent fits poorly as such: Turbo: I didn't have gasket quite centered, but it has a...

So I've driven on my current street tune for roughly 2 months and the other night after crossing vtec it popped real bad and an injector died and dragged a cylinder all the way home. No internal damage was caused but an injector had misfired, spilled some gas into the intake and I guess died. I...

I'm wanting to enter best jdm integra, best suspension, and best overall YEAR/MODEL/MOTOR 1996/Acura Integra/B18C Engine: GSR block (stock), b16 head, full supertech valvetrain (dished valves, dual springs and steel retainers), gsr cams, bwr gears, arp studs, s300 (lots of parts not on but...

I bought this car in 2010 as a project and learning experience, I've always loved cars and imports especially, and something about an integra just called my name. Although she wasn't much to look at, she packed an ls/v with itr pistons and eagle rods and was pretty mean for what she was. Also...

I hate to keep posting but it's a tad abnormal and I want to see if I can fix this, will delete when solved. So temp have dropped to about 50ish during the day but a bit colder at night. Only recently and at night, I've noticed my afr idle and fluctuate toward ~15.2, but during day it runs...

So I finally got around to test fitting my mani and turbo and some of the feed/drain hardware and I have a clearance issue where one of the mounting studs and the oil feed line are. The second pic is a close up showing the stud hitting the surface without the feed flange on. I just wanted to see...

Hey guys, picking up the smaller parts for my turbo install and I just wanted to see if there were any preferred brands or methods to feed/drain lines. Are there any kits better than another? Sandwich plate over t-fitting? I just don't know what to look for until I get feedback on sizing or...

I just wanted to post this up because when I was looking for pics of different brands of gauge pods which would replace my cluster bezel, I couldn't find any that were labelled by brand, or any reviews of the cheaper ones. I bought the Blox one because it was cheap and wasn't autometer(?) which...

Finally bought s300 and got it installed, loaded a basemap to check that everything was working and there's some issues. First off, the sensors will not read in realtime iat,etc. Then, the base map, a usdm p72, which i've been running an actual p72 just fine (limp mode), which starts, but idles...

So I finally decided to buy Hondata but all of a sudden no one around me is selling virgin p28s and anywhere else wants way too much. However, I have a p28 that came with the car that had been chipped (SST chip) and was thinking about basically following the steps on "How to chip your ecu" but...

I've got a few codes causing my car to run in limp mode (hitting 5k and no vtec), and Code 54 for the CKF is the one I can't fix. My question is, could I just do the bypass trick and leave it be or should I really fix this? I've driven almost 600 miles like this and the car drives amazing other...

Hey guys, I currently try have F&f type 1s, maxed in the rear and raise about an inch in the front due to smacking towers. Full Buddyclub camber kits. I purchased the f&f extended top hat and spring combo and will be installing it as soon as it arrives. The top hats are definitely going on, but...

Just throwing out for some info. 3rd Gen Integras. Has anyone else had issues finding replacement clips for your quarter glass? long story short, mine were removed and the clips broke. Called up Acura and all they have even in their catalogue is pieces of tape that apparently go on the windows...

What's up CI, finally got my setup all together and she rides great. I'm riding on maxed out f&f type I which are perfect for me, but, as expected, when I hit bumps (and I mean only the big ones) I slap my buddy club uca on the towers. Yeah I know, raise it, and I'm going to anyway, but, I...

So long story short, my rear glass was removed and Idk how to reinstall it. Can I do it myself, if so how, I have searched and can't find a how to, everyone says buy a new hatch but they're weighing against price of buying a new one. I called glass place and they said 80 to install but if I can...

Looking at some input from fellow RHD converters. I've got all my wiring done EXCEPT the door harnesses so that my switches will be on the proper side. I started to swap them and realized the window motor connectors are completely different, which means I could either swap the buttons and have...

So I installed my BuddyClub P1 Front Camber kit finally and it's great because it's just enough adjustability for my suspension setup, BUT, now my tires have Toe-Out like crazy (like a 5 degree difference left to right. I've been going over everything and I can' find the problem. I assume I can...

I know it seems like a long shot, but I have two dashes for my rhd swap that are both damaged in some way. I was wondering if anyone has ever had them reupholstered, ie the top vinyl section. Because of its drastic shape I'm pretty skeptical that it can be done, but hoping to hear some good...