Search results

alright so i just replaced my climate control i bought off a guy. my switch on my last one had snapped off so i just replaced the whole housing. well, i got the new one today, got it put back in and everything. and well. it blows air BUT it only blows air to the feet. NO MATTER what button i...

alright so i just replaced my climate control i bought off a guy. my switch on my last one had snapped off so i just replaced the whole housing. well, i got the new one today, got it put back in and everything. and well. it blows air BUT it only blows air to the feet. NO MATTER what button i...

alright so first off i want everyone to keep in mind that my car is running a b20 with an ls ecu and its chipped and tuned. well i took my car to get my emissions done to day and it failed for producing to much NOx (nitrogen oxide) failed on both high and low end from what he said but it...

alright. so i went and got my car tuned and today, and here is the sheet. im running a b20 with just headers, intake and exhaust. nothing special other then that

ok, so if all you guys remember, i got my b20 put in back in May. When i got the motor put in, i got a new clutch cause im was going on the frits. Well, over the past month i have noticed that it just doesnt feel right. My Clutch engages high off the floor, and its hard to put it in first and...

alright so within the next few months i will be looking into getting some new suspension for my car. i have ten stech springs and kyb adjustables right now but i want something different. im considering getting a set of full coils that are street oriented and suited for daily driving. i dont...

alright so looking at the haynes manual it says for a crv (b20) the gap need sto be a .043, is that right or wrong? i am asking cause i posted this question on another forum and they are saying .044, is .043 wrong?

alright so i have gotten all the bolt ons that i am wanting to get for the time being; intake/exhaust/header, on my b20. i just recently had problems and now they are fixed all except for the sputtering/putting problem i posted about in my other thread. i am wondering what is yalls take on...

as most of you know i have had to replace my dizzy 2 times within the past 2 months. kinda sucks! anyways, after my engine swap back in late may, early june i started experiencing a "putting" or i guess you could call " sputtering" at idle. I was talking with my dad the other day telling him...

Alright. so i am running into a problem. i just recently replaced the header. being as the header is so damn big, it burnt into one of my radiator fans and it doesnt work anymore. my check engine light now comes on after a certain amount of minutes. When im driving after the engine fights a...

alright so i had purchased the short tube RMF header for an LS to go onto my B20, well that shit dont fit! connects fine to the block but there is about an inch and half to 2 inches maybe of a gap between the header and the cat. On top of that the cat is a two bolt oval shape and the header is a...

alright so i get out of work today and get in my car to go home, turn the key, and nothing. interior lights come on, the motor is turning over, but the motor will not start. did a spark plug test, no spark, tightened the shit out of the battery terminals. I also checked the distributor, the cap...

i am interested in looking for a header and i wanted to know about whether or not there is an o2 sensor attached to it on the stock one. if there is, do i need to take the one that i end up getting to an exhaust shop and get them to attach one to it? thanks in advance

as the title says, i need how toos on how to change my rotors and pads. im doing it tomorrow so please if ya can! thanks!

alright so i have been talking to a guy on another site who was telling me that i can easily clean the IACV instead of buying a new one to install onto the back of the intake mani. what i wanted to know is if anyone had any knowledge of a "how to" on a site that might show me how to do this. If...

liek the title says, does the IACV come with a new manifold if i purchase it?

alright so i need to chang out my rotors and what have you soon. they are warped and causing vibrations on slowing down so i want to get this done soon. what is a good inexpensive break kit in yalls opinion? im not looing to rip my arm off to buy one, i just want something maybe a lil better...

i have the opportunity to purchase a header from someone on another site for like 80 bucks and i am wandering if it is good or not. so are they good? i know eveyone talks about hytech and what not or comptech or greddy, yada yada yada. but are dcsports headers good?

keep in mind it was raining so my cars a lil wet, but yea, i happened to like the pic.

alright so i got a new engine my car a week ago and i love it, i love the way it pulls and what have you. but i am a little concerned. when i start the car up in the morning after sitting all night it idles at about 1500 then it drops down to what looks to be between 7-500 rpm. i adjusted the...