Search results

We get the point. Fact of the matter ebay is know for a place to get the cheapest parts. There for the cheapest coilovers will be deemed ebay coilovers. And we all know you get what you pay for. Ebay coilovers can be interpenetrated as to the cheapest coilovers on the site. You know what he...

Me or the OP?

knock off turbos are garbage at best. I got one for free from a friend of mine that he decided not to use thanks to my recommend so we slapped it on my 88 turbo RX-7 it lasted 300 miles before total destruction LOL. The turbine wheel came in contact with the housing and sounded like a...

My car makes a hiss that sounds like a turbo spooling in every gear under certain throttle input. Then again i have a Skunk2 intake manifold and throttle body and a SR intake. I love the sound it makes it does it from like 2500 rpm to 4000 rpm under light throttle.

Dude dont sell it man! ! ! It takes time and effort and money to build a nice car. You just going to sell it now???? Keep it and be content with a car you built, unless you dont like it any more.

Most height adjustment will need alignment to some degree just with a lower drop you will need less adjustment. You can start with ground control coil overs and lower it a bit but the shocks wont last long at the stiffer spring rate. Dont buy lowering springs if you want to go low you will be...

Invest in some maintenance first IMO if not done already. Change timing belt(Unless previous owner gave you a receipt with mileage on timing belt job), Replace spark plugs, Flush cooling system, Oil Change, PVC valve, etc,,, If you have money left over then plan out your next mod. Coil overs...

Sounds to me like your clutch is not fully engaging. While its cold the clutch grabs, but as you drive it and its spinning when it should be stationary causes it to over heat and loose grip. You mentioned your car smells bad, could be the clutch burning. I would not take it to that shop IMO. A...

any one selling a rug for me?

^ Good Idea You have the gsr head to put on the b20 and you are golden. Some arp head studs, gsr pumps, and some arp rod bolts are a must. Have you thought about rebuilding the bottom end?

rather not spend the money if i band-aid it i cant see the wound. catch my drift.

No did not vacuum dont have one had to go to the gas station after to vac. LOL Thanks for noticing. LOL

I didnt see the j/k part i was like WTF this guy talking about LOL

Me im in west Kendall got a nice little town house im renting.

I have the old greddy sp2 and i think for the quality of the sound it is worth the extra coin. The new greddy SE is the predecessor of the SP2 should give you a great tone just like the SP2. Even after my CAT was removed the sound level was almost the same as with the CAT. You get what you...

lol@ 00DC2TW Here are a few more shots. Dont mind the hanging cable I was doing some maintenance on the battery. I also need a paint job. Front Ass Shots. Tegs have a nice ass. LOL

I need a little bump It is only a 12" with a 250watt rockford fosgate amp bolted on the back. It is really light for how it sounds.

Car is spic and span. Just need a new rug and the seats reupholstered. I hate having that rug jacked up. Looking for a black rug and oem INTEGRA floor mats or just some black floor mats with "INTEGRA" in gray. Comments/Suggestions Welcome Drivers Side Engine Bay X2 Passenger...

My tires before the alignment went down to the poly thread on the inner part of the tire only. the flat section looked like new and all that was off was my toe setting. my car is cambered a bit but the alignment guy told me at the rate the tire wears at this camber does not justify the cost of...

Agreed with every one above. No point in dropping an ITR motor in if you are going to do boost. Most people use an ITR motor for N/A high rpm fun. You can use a B16 for all it matters if you are going boost, you still need to swap pistons and rods. Think about it ITR Motor = High intial cost +...