Search results

Some supercharger kits usually the cheaper ones kreftwerks say you need to remove the ac compressor to install the kit. I can't find anywhere in the description of the CT Engineering Supercharger Kit for the 05 rsx type s needing to remove the ac compressor. Yes it's 4k for the reflashed ecu...

Buying the skunk2 2" lowering springs and aftermarket struts to support (please post any recommendations for best combo struts for these springs). Have stock 05 rsx type s rims on. Will there be any wheel/fender rub happening? Searched the forums and couldn't find my answer. My apologies if...

I see they discontinued the tuner series Springs and titanium retainers. Does anybody know if that means you can use the alpha series Springs Valves and titanium retainer kit with the tuner series camshafts? I know it says the alpha valve train kit is not compatible with the pro series...

Car is a 94 integra lowered on about 1.64" springs. What tire size should I use? I want best traction and am going to be buying Z rated tires. Thanks! Sent from my Samsung Galaxy Note 3 using Tapatalk

Well it turns out my clutch is starting to slip at 3500 rpms in first n second gear. It's a stock type r so I need some opinions. Motor is a 98vb18c spec type r. Exedy stage 1 or 2 racing clutch a good choice n which one? The most I'm gonna do is skunk 2 tuner cams and gears and spring valves...

Okay have a 98 spec r type r motor in my 94 teggy. Dumped it down to third from 5th and it revved to high so i quickly disengaged it and put back in 5th. Then i smelt the infamous burning smell through the vents. I assume i burnt the clutch. Problem is i have hasport motor mounts and the...

Is this possible? I know my motor doesn't have the vtec oil pressure switch and it description it only says compatible with so I assume it can be hooked together if needed or in my case I don't have to since I don't have one. Someone please explain lol. Sent from my SM-N900V using Tapatalk

Have 98 jdm type r swap. Leaking Distributor o ring. Vtec when engaging suddenly became smooth and not loud. THIS IS AN INTEGRA TYPE R so what gives? It usually cracks really LOUD when engaging. I even made sure oil level was full and still no difference. Haven't gotten a chance yet to fix...

94 integra ls w/ 98 b18c type r. Drove car to parents. Couple hours later start car and notice it wont go past 4,000rpms. No check engine and all omoters work. Any ideas? Speed Sensor? Sent from my DROID X2 using Tapatalk 2

hello guys i got a 98 jdm b18c type r motor in my integra. One friend is saying 68mm skunk2 pro throttle body is better and the other is saying to use the 70mm. Not going turbo. any thoughts on which size would be better for all motor? Sent from my DROID X2 using Tapatalk 2

Not sure which is better for someone short like myself. Im 5 foot 5 inches Any recommendations? I want a short length sticking straight up. I bought a skunk2 single bed but haven't installed it yet so i can still exchange for a dual bend if recommended..... Sent from my DROID X2 using...

Im in 5th gear and going 80mph and my rpms will be at 4800-5000K. I do have a 98 JDM B18c Spec Type R motor w/ LSD tranny in my 94 Integra LS 2DR. From what I've read my tranny has short gears but thats ridiculous. Its acting like their should be a 6th gear almost. Apparently the GSR...

Which Motor Mounts can I Use For Type R Swap? Car: 94 Integra LS 2DR w/ B18c Type R swap 1) Do I use Integra LS motor mounts or can I use Type R. 2) Besides hasport what other brand motor mounts come close to hasport quality but dont cost as much. Sent from my DROID X2 using Tapatalk

Car: 1994 Acura Integra LS w/ swapped 1998 JDM B18c Type R motor. After filling up gas one day I attempted to start car and the followjng occured: - Car would start then start rumbling and and struggle to stay on. It would then cut off. This occured 4 more times. Even if I would put into...

Car: 1994 Acura Integra LS w/ swapped 1998 JDM B18c Type R motor. After filling up gas one day I attempted to start car and the followjng occured: - Car would start then start rumbling and and struggle to stay on. It would then cut off. This occured 4 more times. Even if I would put into...

Hello Again, According to ngksparkplugs.com the Gap for the NGK PFR6G-11 spark plugs is 0.044" for the 1998 USDM B18c ITR. I have a 1998 JDM B18c ITR motor. If I used the NGK PFR7G-11 spark plugs would I also gap them to 0.044"? The difference betwern the USDM B18c and JDM is USDM is 10:1:0...

Can someone please tell me what the stock spark plug gap would be for a 98 JDM B18c Type R Motor? Motor is stock and I believe stock is at 11:1:0 compression. Spark plugs are NGK Spark Plug 6 Temperature. Sent from my DROID X2 using Tapatalk 2